Electro-Pneumatic Positioner IP8000/8100 Series (Lever Type / Rotary Type)

Download

Product Specifications

Product Specifications

Items	Part number
	IP8000		IP8100
	Electro-pneumatic positioner
	Lever type lever		Rotary type cam
	Single acting	Double acting	Single acting	Double acting
Input current	4 to 20 mA DC (standard)^*2)
Input resistance	235±15Ω (4 to 20 mA DC)
Supply air pressure	0.14 to 0.7 MPa
Standard stroke	10 to 85 mm (Allowable runout angle 10 to 30°)		60 to 100°^*3)
Sensitivity^*4)	0.1% F.S. or less	Within 0.5% F.S.
Linearity^*4)	Within ±1% F.S.	Within ±2% F.S.
Hysteresis^*4)	0.75% F.S. or less	Within 1% F.S.
Repeatability^*4)	Within ±0.5% FS
Temperature coefficient	0.1% F.S./°C or less
Supply pressure fluctuation	0.3% F.S./0.01 MPa or less
Output flow rate^*6)	80 L/min (ANR) or higher (SUP = 0.14 MPa), 200 L/min (ANR) or higher (SUP = 0.4 MPa)
Air consumption^*6)	5 L/min (ANR) or less (SUP = 0.14 MPa) 11 L/min (ANR) or less (SUP = 0.4 MPa)
Ambient temperature and operating fluid temperature	General structure: -20 to 80°C
	TIIS explosion-proof: -20 to 60°C ATEX intrinsically safe explosion-proof: -20 to 80°C (T5) -20 to 60°C (T6) -40 to 60°C (T6) / -L type low temperature specifications
Explosion-proof structure^*7)	TIIS explosion-proof construction (Exd IIBT5) ATEX intrinsically safe explosion-proof structure (II2G Ex ib IICT5/T6)
ATEX intrinsically safe explosion-proof Parameters (current circuit)	Ui ≤ 28 V, Ii ≤ 125 mA, Pi ≤ 1.2 W Ci ≤ 0 nF, Li ≤ 0 mH
Outer cover protective structure	JISF8007 IP65 (compliant with IEC 60529)
Air connection port^*8)	Rc1/4 female thread, NPT1/4 female thread, G1/4 female thread
Electrical wiring connection port^*8)	G1/2 female thread, M20 × 1.5 female thread, NPT1/2 female thread
Material/painting	Main body: die-cast aluminum / modified epoxy-based baked coating
Weight	Approx. 2.4 kg (without terminal box) / Approx. 2.6 kg (With terminal box)

*1) The specification values are at room temperature (20°C).
*2) Standard products are available for 1/2 split range. For use with 1/2 split range, please add 1% respectively to the linearity and hysteresis characteristics in the specification table.
*3) The stroke adjustment of 0 to 60° and 0 to 100° is possible.
*4) Accuracy-related characteristics vary depending on the combination with other equipment consisting the loop, such as positioners and actuators.
*5) Pressure fluctuation will not cause any changes in the output, however, if supply pressure setting is changed after the last calibration, please adjust the balance current and perform calibration again.
*6) Air is constantly consumed. Note that (ANR) refers to JIS B0120 standard air.
*7) For explosion-proof structure and HART communication, models must be specified.
*8) Screw types can be specified by selecting the model.

Product Specifications

Items		Part number
		IP8100-0□1-J/JR (Non explosion-proof)
		Electro-pneumatic positioner
Analog Output	Wiring method	2-wire type
	Output signal	4 to 20 mA DC
	Power supply voltage	DC12 to 35 V
	Load resistance	(Power supply voltage – 12 V) ÷ 20 mA DC or less
	Accuracy	±2% F.S. or less^*1)
	Hysteresis	Within 1% F.S.

*1) It indicates the analog output accuracy for the actuator angles.